Kicker ZX550.3 Bedienungshandbuch PDF herunterladen (Seite 2)

+12V

18"

(45cm)

24"

(60cm)

Installation

1. Mounting Choose a structurally sound location to mount your Kicker ampliﬁ er. Make sure there are no

items behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm)

of open ventilation for the ampliﬁ er. If possible, mount the ampliﬁ er in the climate-controlled passenger

compartment. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the

ampliﬁ er.

2. Wiring Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to

the ampliﬁ er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint and corrosion free

solid metal area of the vehicle's chassis. Adding an additional ground wire of this same gauge (or larger)

between the battery's negative post and the vehicle chassis is recommended.

The ZX ampliﬁ er has dual input sensitivity differential RCA inputs which will receive either high or low level

signals from your car stereo’s source unit. Ideally, when connecting the source unit to the ampliﬁ er, the

ZX ampliﬁ er’s input level switch should be set to “LO” and a low-level signal should run from the source

unit’s stereo RCA output to the stereo RCA input on the end panel of the ampliﬁ er using RCA interconnect

cable. If a low-level stereo RCA output is not available on the source unit, the signal can be delivered to the

ampliﬁ er using the high-level speaker outputs on the source unit. Set the input level switch on the end panel

of the ampliﬁ er to “HI”. Crimp and solder RCA connectors to the end of the speaker wire running from the

high-level speaker outputs on the source unit and connect the wire to the RCA Inputs on the end panel of

the ampliﬁ er as shown in Figure 1.

Keep the audio signal cable away

from factory wiring harnesses and

other power wiring. If you need to

cross this wiring, cross it at a 90

degree angle.

Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your ampliﬁ er.

If you ever need to remove the ampliﬁ er from the vehicle after it has been installed, the ground wire should

be the last wire disconnected from the ampliﬁ er--just the opposite as when you installed it. See the chart

below for power and ground wire size, and fusing recommendations.

3. Conﬁ guration The following diagrams show the most common conﬁ gurations for your Kicker ZX series

ampliﬁ er.

(ZX700.5) Four Channel Operation with Subwoofer ZX700.5 ampliﬁ ers are capable of operating into

a minimum impedance of 2 ohms per channel in stereo operation and 2 ohms mono in the subwoofer

channel. See Figure 2.

(ZX550.3) Two Channel Operation with Subwoofer ZX550.3 ampliﬁ ers are capable of operating into

a minimum impedance of 2 ohms per channel in stereo operation and 2 ohms mono in the subwoofer

channel. See Figure 3.

ZX.3/ZX.5SeriesAmpliﬁ er

Owner’sManual

MultiChannelModels: ZX550.3 / ZX700.5

Authorized Kicker Dealer:

Purchase Date:

Ampliﬁ er Model Number:

Ampliﬁ er Serial Number:

Congratulations on your

KICKER purchase!

Please record your purchase

information and keep your sales

receipt for validation of warranty.

__________________________

INSTALLATION

ZX.3/ZX.5AMPLIFIER

CONFIGURATION

+12V

18"

(45cm)

24"

(60cm)

Figure 3

Figure 4

Ground

Remote

Turn-On

Fuse

Battery

Ground

Remote

Turn-On

Fuse

Battery

(ZX700.5) Four Channel Operation with Subwoofer

(ZX550.3) Two Channel Operation with Subwoofer

Note: To get the best performance from your new Kicker Ampliﬁ er, we recommend using genuine Kicker Accessories and Wiring.

Performance

Model ZX550.3 ZX700.5

RMS Power in Watts, AMP 1 and AMP2 all channels driven

@14.4V, 4Ω stereo, ≤ 1% THD+N 70 x 2 70 x 4

@14.4V, 2Ω stereo, ≤ 1% THD+N 85 x 2 85 x 4

@14.4V, 4Ω mono, ≤ 1% THD+N N/A 165 x 2

RMS Power in Watts, SUBWOOFER channel driven

@14.4V, 4Ω mono, ≤ 1.5 % THD+N 210 x 1 210 x 1

@14.4V, 4Ω mono, ≤ 1.5 % THD+N 420 x 1 420 x 1

Length: in(cm) 16 3/4 (42.5) 20 (50.7)

Speciﬁ cations common to all models:

Height: in(mm) 2 1/8 (54mm)

Width: in(mm) 9 5/8 (244mm)

Frequency Response, ± 1 db: 25 Hz - 20 kHz

Signal-to-Noise Ratio: >95db, a-weighted, re: rated power

Input Sensitivity:

Low Level: 125mV-5V

High Level: 250mV-10V

Selectable Electronic Crossover:

Variable HI or OFF (Bypass), 50 - 200Hz,

12dB per octave

Subsonic Filter: 24 db/Octave Subsonic Filter Fixed @ 25Hz

Bass Boost: Variable 0 to +18dB Bass Boost @ 40Hz

Core Cable

Ground or Shielding

High-level Speaker Output Wire

To Ampliﬁ er

To Source Unit

Figure 1

ModelZX550.3 1 (ONE) 60 AMPERE FUSE PowerGroundWire 4GA

ModelZX700.5 1 (ONE) 90 AMPERE FUSE PowerGroundWire 4GA

1 2 3 4

Kommentare zu diesen Handbüchern

Keine Kommentare

Kicker ZX550.3 Bedienungshandbuch Seite 2

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Auto-Audio-Verstärker Kicker ZX550.3